Skip to content

Aircraft corrosion control

Aircraft Wash Rack and Clear Water Rinse Facility

Salt spray settles on every aircraft that flies low over the sea, and salt on bare metal starts corrosion. A rinse facility on the taxiway washes it off on the way back to the stand. The crew taxis onto a steel deck, starts the rinse by radio and taxis off rinsed. The water goes back to be treated and used again.

A large grey helicopter parked with its rotors stopped on a wide steel rinse deck with a full-width ramp, water arcing onto it from cannons set in pits beside the deck, two KKE process containers on the apron behind and the sea beyond

What an Aircraft Rinse Facility Does

Helicopters and aircraft that operate near the sea collect salt on every surface: the airframe, the landing gear, the rotor head, the engine intakes. Corrosion control manuals for military aircraft call for a fresh water rinse after flights through salt air, and for a whole fleet the quickest way to do it is a rinse facility on the route back to the stand.

It goes by several names: a clear water rinse facility, a bird bath, an aircraft wash rack. It is not a full wash. There is no detergent and no hand work. It is a deluge of clean water from nozzles in the deck and water cannons at its corners, which takes salt and dust off in a few minutes while the aircraft sits on the deck. A full wash still happens in the hangar or on a wash pad, far less often.

Plan it

Plan Your Aircraft Rinse Facility

Four short cards about your aircraft and your site. You get an outline of the facility straight away, and an engineer gets what is needed to size it and quote.

How the outline is worked out

  • The deck is sized by the largest aircraft: light helicopters and jets on a smaller deck, heavy-lift helicopters and tiltrotors on a larger one, large transport aircraft on a deck engineered to their landing gear.
  • Four water cannons stand clear of the rotor disc or the wingtips, with one rinse programme for each aircraft type.
  • Reverse osmosis treats the make-up water unless the supply is potable, and even then the water analysis decides.
  • The treatment, pumps and controls go in two insulated containers, fitted and tested at our works.
  • Pavement, pits, the container pad and the utility connections are built by others, to our drawings.

The outline is a starting point, not a design. An engineer checks it against your aircraft data and your site before anything is quoted.

Step 1 / 4

The Aircraft

Tick every type that will use the facility. The largest one sets the size of the deck.

Aircraft that will be rinsed
Largest aircraft: rotor diameter or wingspan
Largest aircraft: maximum take-off weight

If you know it. It decides the deck structure.

Step 2 / 4

How It Will Be Used

The busiest hour sizes the water treatment, not the average day.

Aircraft to rinse in the busiest hour
How often each aircraft is rinsed
Who starts the rinse
Step 3 / 4

The Site

The equipment is built for your supply and your climate.

Electrical standard
Site temperatures through the year
Where the deck will sit
Step 4 / 4

Water and Scope

Rinse water has to be clean enough to put on an aircraft, so the supply matters.

Fresh water supply
Where rejected water can go
Rinse water quality to meet
2-year operating spares
Timeline

Taxi on, rinse, taxi off

How an Aircraft Is Rinsed

01

Taxi onto the Deck

The aircraft taxis up a low ramp onto the steel deck and stops where the signal head shows. Presence sensors confirm it is on the deck and stopped.

02

Start the Rinse from the Cockpit

The crew starts the rinse by radio, with a set number of microphone clicks on an assigned frequency, so no ground crew is needed. The number of clicks can pick the rinse programme for the aircraft type.

03

Underside First, Then Top Down

Nozzles in the deck rinse the underside and landing gear, while the water cannons work up the lower surfaces and then rinse from the top down, in the order the programme sets for that aircraft.

04

Taxi Off, Water Back

The signal changes to proceed and the aircraft taxis off. The water that landed on the deck runs to gutters along its sides and is pumped back to be treated for the next aircraft.

The rinse deck

A Steel Rinse Deck Built for Aircraft

The deck is bolted together from the same modular steel deck sections as our heavy-duty wash racks, on a level pavement, with ramps at each end and collector gutters along both sides. Pictured here as a vehicle wash rack: the aircraft deck is wider, has no splash walls, and carries nozzles in its centre.

  • Designed for the aircraft that will use it. The deck and ramps are checked against the aircraft's wheel loads and tyre pressures, with structural calculations and a proof load test before delivery.
  • Nothing loose on the surface. Flush, locked fasteners and recessed nozzles keep the deck free of foreign object debris.
  • Low ramps. The approach and departure ramps are long and shallow, for aircraft with little ground clearance.
  • Stainless nozzles in the deck, adjustable for angle, with interchangeable tips, rinse the underside and the landing gear.
A KKE modular steel deck built as a vehicle wash rack on a concrete pad, with access ramps at the near end and green splash guards along both sides

Water cannons

Water Cannons That Reach the Whole Airframe

Water cannons at the corners of the deck rinse what the deck nozzles cannot reach: the upper fuselage, the tail, the rotor head and the upper surfaces of the wings.

Programmed Sweep Paths

Electric pan and tilt with position feedback, and a rinse programme for each aircraft type.

Clear of the Rotor Disc

The cannons stand outside the rotor disc and the wingtips, low enough to sit in pits beside the deck.

Calculated Against Downwash

For helicopters and tiltrotors, the reach of each stream is calculated with the rotor downwash present, and the cannon pressure is set from it.

Rinsing, Not Blasting

The water meets the surface at a shallow angle, so it rinses the salt off rather than driving it in.

Wind Corrected

An anemometer corrects the aim for wind, and holds the rinse when the wind is too strong.

Drained After Each Rinse

The cannons and the deck manifolds drain after every cycle, so nothing stands in the lines.

Water

Rinse Water That Is Recovered, Treated and Checked

A rinse uses a lot of water, and the water has to be clean enough to put on an aircraft. So it is caught, treated, checked and used again, and only what fails the check goes to the drain. More on water recycling.

Caught on the Deck

Gutters and outlet boxes along the deck catch the rinse water and pump it to the treatment container.

Filtered and Skimmed

Self-cleaning screen filters and bag filters take out sand and grit, and a skimmer takes off free oil.

Disinfected

UV and chlorine dosing keep microorganisms out of the stored rinse water.

Made Up with Clean Water

Reverse osmosis treats the make-up water when the local supply is too salty or too hard to rinse with.

Checked All the Time

Online analysers watch conductivity, pH, turbidity, chlorine and temperature, on the fresh water and the recycled water alike.

Discharged When It Fails

Water outside the limits is discharged automatically and replaced with fresh water.

Controls and safety

Activation, Signals and the Process Containers

The pumps, the treatment and the controls go in two insulated containers beside the taxiway, fitted and tested at our works before they ship.

Crew Activation by Radio

Microphone clicks on an assigned frequency start the rinse, so no one has to be on the deck.

Signal Heads

Stop, rinse and proceed, at the deck entry and exit, so the crew always knows when to move.

Presence Sensors

The rinse starts only with the aircraft stopped on the deck, and stops if it moves.

Ground Control Station

Local start, programme selection and an emergency stop, with a handheld wireless remote.

Two Process Containers

Insulated, with heating and cooling: one for recovery and treatment, one for the rinse tank, pumps and controls.

Pumps on Variable-Speed Drives

Pressure is set per programme, and every cycle, flow and water reading is logged.

Specifications, Standards and Tenders

We do not publish flows, pressures or tank sizes for an aircraft rinse facility, because they come from the aircraft, how many are rinsed in the busiest hour, and the site's water. Our engineers size them for each project and put them in the technical proposal, with the P&ID, the general arrangement and the calculations.

Rinse water limits usually come from the operator's corrosion control manual, such as NAVAIR 01-1A-509. Tell us which one applies and we design the treatment and the monitoring to it. We make no claims to aviation or military approvals we do not hold. Electrical equipment is built to IEC as standard, and UL-listed equipment can be supplied where the project needs it.

The pavement, the recovery curb, the pits for the water cannons, the container pad and the utility connections are built by the airfield's civil contractor, to our drawings. If the facility is part of a larger airfield project, we work as the equipment supplier to the main contractor and prepare the drawings, data sheets and technical proposal the tender asks for. For vehicles on the same base, see military vehicle wash systems.

Aircraft Wash Rack — Common Questions

Is an aircraft rinse the same as an aircraft wash?

No. A wash uses detergent and hand work, in a hangar or on a wash pad, every few weeks. A rinse is clean water only, takes a few minutes, and is done after flights through salt air. Most operators need both; this page is about the rinse.

Can helicopters be rinsed with the rotors turning?

That is how a taxi-through rinse is normally used: the aircraft stays running, the crew starts the rinse by radio and taxis off afterwards. The cannon reach is calculated with the rotor downwash present, so the water still reaches the upper surfaces.

Can fixed-wing aircraft use the same facility?

Yes. The deck, the ramps and the cannon programmes are designed for every aircraft type that will use the facility, so tell us the types at the start. Each type gets its own rinse programme.

How much water does it use?

Most of it is caught, treated and used again. Fresh water replaces what is lost to spray, wind and evaporation, and what is discharged when it fails the quality check. The treatment and make-up are sized from the aircraft in the busiest hour and a water analysis of your supply.

What if the local water is salty or hard?

Then the make-up water goes through reverse osmosis before it reaches the rinse tank. We size the unit from a water analysis of your supply.

Who builds the pavement, the pits and the pad?

Usually the airfield's civil contractor, to our drawings. We supply the equipment, supervise its installation, commission it, tune the rinse programmes with the aircraft and train the operators.

Does it work in a cold climate?

Yes, if it is designed for it from the start. The cannons and the deck manifolds drain after every rinse, exposed lines are protected, and the containers are insulated and heated.

Tell us about the airfield

Which Aircraft, and How Many in the Busiest Hour?

Used the questionnaire? Your answers are already in the message below. Otherwise, tell us the aircraft types, how many need rinsing at the busiest time, and where the facility will go. We will come back with a layout and what it needs from the site.

We use your details to respond to your enquiry. See our Privacy Policy for how we handle your data.

Chat on WhatsApp